52.70.Kz Optical (ultraviolet, visible, infrared) measurements
Refine
Document Type
- Doctoral Thesis (6)
Has Fulltext
- yes (6)
Is part of the Bibliography
- no (6)
Keywords
- Leuchtstofflampe (3)
- Brennfleck (2)
- Emission (2)
- Glimmentladung (2)
- Hochfrequenzplasma (2)
- Kathode (2)
- Xenon (2)
- electrode (2)
- erosion (2)
- Abstimmbarer Laser (1)
Institute
With the growing importance of advanced lighting technologies, customers expect additional functionality and higher comfort from fluorescent lamps. However, the ability to regulate light intensity (dimmed operation), in particular, exerts enormous stress on fluorescent lamps’ electrodes, leading to increased electrode erosion and significantly reduced lifetimes. During the operation of a fluorescent lamp, free barium (the main compound of the electrode emitter) is produced at the electrode responsible for lowering the work function in order to enable energy-efficient and durable electrodes with lifetimes of up to 20,000 hours. Despite their relatively long lifetimes, electrodes remain the lifetime-limiting factor of a fluorescent lamp. Therefore, for practical applications (e.g., maintaining quality control, adjusting operational parameters, and evaluating new electrode designs), electrode erosion is of special interest. The actual erosion-measurement methods determine a time-averaged erosion level over several hundred operation hours. Thus, a quasi-instantaneous measuring method (short measurement) is still necessary to determine erosion during operation. Such a method would allow us to compare erosion under different discharge conditions (currents, frequencies, or heating currents) from the same electrode in the same lamp. This work focuses on the determination of absolute electrode erosion during the stationary operation of commonly used fluorescent lamps. Commercial T8 lamps (fluorescent lamps with a diameter of 8/8 inch) are investigated at the operating mode of commonly used electronic ballasts with frequencies of several kHz. Operations under standard and dimmed conditions with an additional heating current to reduce electrode erosion are investigated. Electrode erosion is characterized by the erosion of barium, the main compound of the electrode. Therefore, laser-induced fluorescence (LIF), which is the most sensitive method for this application, is applied to determine the absolute densities of the eroded barium in the electrode region. These densities are affected by the plasma in the electrode region and do not directly represent the absolute barium erosion. To overcome this limitation, a new method based on a special measurement technique in combination with a barium-diffusion-model is developed to determine the absolute barium erosion based on the measured densities. It has been found that the barium densities in the electrode region are lower than the equilibrium pressures produced by the reduction of the barium oxide. This could be caused either by a reduced reaction rate, the reduced diffusion of the reactant (primarily barium oxide) or by reduced barium transport through the porous emitter. However, these results suggest that barium erosion depends on temperature and emitter structure, which vary over an electrode’s lifetime. For currents significantly higher than the nominal lamp current, a drastic increase in emitter evaporation is found. Such, an increase in the lamp current from 300 mA to 500 mA leads to an increase in emitter evaporation by a factor of five. Using the lamp for a long period of time under these conditions therefore reduces the lifetime by a factor of five. Notably, at this dramatically increased erosion level, the hot spot temperature only increases from 1120 K to 1170 K. Investigation of various frequencies from 50 Hz to 5 kHz revealed no significant dependence of emitter evaporation on frequency.
In this thesis, a stereoscopic camera system is presented that is designed for the use on parabolic flights for the investigation of dusty plasmas under microgravity conditions. This camera system consists of three synchronously triggered high-speed cameras observing a common volume of approximately (15 × 15 × 15) mm³ size. In this volume, the three-dimensional trajectories of a large number of particles surrounded by a dense dust cloud were reconstructed. For this task an intricate set of reconstruction algorithms has been developed, including a four-frame linking algorithm and a complex combined 2D/3D tracking algorithm for a reliable tracking of 3D particles. Furthermore, these algorithms effectively suppress so-called ghost particles in the evaluation process which are reconstructed from falsely identified 2D particle correspondences. Dusty plasmas under microgravity conditions are of special interest due to their complex structure and the variety of observable dynamic phenomena. Under typical discharge conditions, a central dust-free void is formed, surrounded by a dense particle cloud. Since the void is inherently dust-free, particles shot into the void can be uniquely identified and used to probe plasma properties inside this region. In the dust cloud itself, processes like self-excited dust-density waves can be observed under suitable experimental conditions. Using the presented camera setup and reconstruction algorithms, two parts of a dusty plasma under microgravity on parabolic flights are investigated. Initially, the force field creating and sustaining the central void is deduced and characterized. The combination of ion drag and electric field force is measured and compared to current models of the ion drag, showing a good agreement with these models. While previous investigations on the forces were limited to two-dimensional slices through the void, our measurements represent the first three-dimensional quantitative analysis of a large fraction of the void region. From this analysis the structure of the force field is determined and separated into a radial and a non-radial (or orthogonal) contribution. It is shown that the radial contribution dominates in the central void, while non-radial forces increase in magnitude close to the void edge. The radial domination is also observed in the velocity distribution of the probe particles which is significantly shifted to radially outward directed velocities for particles leaving the void. Assuming a strictly radial force profile in the horizontal mid-plane of the void, the friction coefficient determining the interaction of the probe particles with the neutral gas background is experimentally determined and shown to match the theoretical expectation. Subsequently, particles at the outer surface of the dust cloud are reconstructed. There, the particles are found to oscillate due to dust-density waves propagating through the high-density dust cloud. For the investigation of the correlation between waves and oscillating particles, the instantaneous wave and oscillation properties are determined and the instantaneous phase difference is obtained. Modeling the probe particles as driven, damped harmonic oscillators, these phase differences between waves and particles are interpreted with respect to the resonance frequency of the oscillating particles. Spatial variations of the phase difference are observed that may be attributed to different frequencies of the dust-density waves, or to changes of the resonance frequency induced by changing local plasma parameters. From a few measurements of particles oscillating at their resonance frequency, information about the surrounding plasma or properties of the particles themselves can be deduced. However, a larger number of reconstructed trajectories is necessary in order to interpret the phase differences on a reliable data basis. The presented camera setup in combination with the evaluation algorithms is a flexible system for the investigation of three-dimensional dusty plasmas. Its robust construction allows the operation of the system in challenging environments such as on parabolic flights, where spatial limitations and vibrations produced by the aircraft make special demands on such a diagnostic tool. This versatility makes our stereoscopic camera setup and the reconstruction process a suitable standard diagnostic for the application with dusty plasmas; this system will therefore be used in future research amongst other things for the investigation of boundary layers in extended three-dimensional dust clouds under microgravity.
In der vorliegenden Arbeit wurde die Katodenregion einer quecksilberfreien Helium-Xenon Niederdruckentladung im Brennfleckbetrieb experimentell untersucht. Diese Region ist von besonderem Interesse, da sich hier die Elektronenemission, die Erzeugung von Ionen und metastabilen Atomen sowie lebensdauerbegrenzende Prozesse abspielen. Um die Entladung im Brennfleckbetrieb zu realisieren, kam als Katode eine im Rahmen dieser Arbeit entwickelte neuartige planare Geflechtelektrode zum Einsatz. Mit der Methode der ortsaufgelösten Laser-Atom-Absorptionsspektroskopie (LAAS) wurden die absoluten Teilchendichten der zwei untersten angeregten Xe-Atome und die Gastemperatur in der Katodenregion bestimmt. Die Inhomogenität des Spot-Plasmas fand dabei besondere Berücksichtigung. Sowohl die Teilchendichten der zwei untersten angeregten Xe-Atome als auch die Gastemperatur sind unmittelbar vor dem Brennfleck maximal und fallen in axiale und radiale Richtung stark ab. Insbesondere die Gastemperatur beträgt in einem Abstand von 1 mm vor dem Brennfleck circa 650 K und liegt damit deutlich über Raumtemperatur. Des Weiteren ließ sich die Temperatur im Brennfleck auf der Katodenoberfläche mittels optischer Emissionsspektroskopie ermitteln. Dies geschah durch Anpassung des aufgenommenen Spektrums an die Plancksche Strahlungsgleichung. Die Brennflecktemperaturverteilung weißt ein ausgeprägtes Maximum auf, das je nach Entladungsstromstärke maximale Werte zwischen 1414 K bei 40 mA und 1524 K bei 80 mA annimmt. Von diesem Maximum aus wurde ein starker in alle Richtungen nahezu symmetrischer Temperaturabfall festgestellt. Ein technologisch wichtiger Aspekt hinsichtlich der Lebensdauer einer auf Xenon basierenden quecksilberfreien Lampe ist der negative Effekt der Xe-Gasaufzehrung. In dieser Arbeit wird gezeigt, dass die Gasaufzehrung unter Verwendung der planaren Geflechtelektrode im deutlichen Gegensatz zur industriell gefertigten Becherelektrode, wie sie vielfach in Lampen für Lichtwerbung vorkommt, vernachlässigbar klein ist. Dies wird auf die Ausbildung eines heißen Brennflecks und die damit verbundene hohe Katodentemperatur und niedrige Katodenfallspannung zurückgeführt.
Asymmetrical capacitively coupled RF discharges in oxygen, argon and hydrogen have been experimentally investigated with the innovative technique of the phase resolved optical emission spectroscopy. This diagnostic tool allows to measure spatio-temporally resolved emission intensities of electronically excited species with a high resolution. The spatial (axial) resolution was better than 1 mm and a temporal resolution of about 1.5 ns has been achieved. Therefore the plasma induced optical emission within the RF cycle (TRF = 73.75 ns) from the RF sheath region with a typical mean sheath thickness of about 5mm has been studied. Spatio-temporally resolved optical emission patterns of the following optical transitions have been measured for a total gas pressure in the range of 20 to 100 Pa and self-bias voltages between -50 and -550 V: Oxygen plasma Emission at 777.4 nm and 844.6 nm (atomic oxygen) Argon plasma Emission at about 751 nm and 841 nm (argon) Hydrogen plasma Emission at 656.3nm (atomic hydrogen, H alpha-line) These transitions are the most prominent ones of the investigated excited species in these plasmas as could be shown from overview spectra of the plasma induced optical emission in the range from 350 to 850 nm. For the first time such extensive PROES measurements in oxygen CCRF plasmas are presented in this work. The additional investigations of argon and hydrogen plasmas serve as a reference and for a direct comparison with results from the literature. The temporal behavior of the emission intensity is influenced by the effective lifetime of the emitting states which is on the order of the nanosecond time scale of the RF cycle. Therefore, it does not represent the real temporal behavior of the excitation. A simple method has been applied to calculate relative excitation rates from the measured emission intensities to distinguish different excitation mechanisms and their correct relative temporal behavior. In a close collaboration within the framework of the Sonderforschungsbereich Transregio 24 'Fundamentals of Complex Plasmas' a newly 1d3v PIC-MCC code for simulations of capacitive RF discharges in oxygen has been developed by Matyash et al. The very close coupling of experiment and modeling allowed a really detailed and microscopic understanding of the processes and dynamics from the sheath to the bulk plasma in CCRF discharges. The spatio-temporally resolved excitation rate profiles show four different excitation structures (I-IV). Excitation processes due to the following mechanisms in CCPs could be identified and characterized: I Electrons expelled from growing sheath II Electrons detached from negative ions (collisions with neutrals) + secondary electrons from the electrode surface (ion bombardment) III Field-reversal effect, reduced mobility of electrons (electron-neutral collisions) IV Heavy-particle collisions These excitation mechanisms are characterized by different temporal and spatial behaviors of the excitation rate within the RF cycle. Additionally it has been shown that the excitation by electron impact in the investigated oxygen plasmas results mainly from dissociative electron impact excitation (O2 + e -> O + O* + e) and not from direct electron impact excitation (O + e -> O* + e). Actinometry measurements show that the results are not really credible. Thus actinometry is not applicable on the investigated oxygen RF plasma. A challenge in interpretation is the observed excitation pattern IV. Pattern IV has to be caused in connection with heavy particle collisions nearby the electrode surface and could be observed in all the three plasmas oxygen, argon and hydrogen. It is located directly in front of the powered electrode and appears during almost the whole RF cycle. The temporal modulation is nearly sinusoidal and weak in comparison to the first three patterns. This is due to the weak RF modulation of the ion flux towards the electrode surface which has been proven by a PIC simulation. It could be shown that the modulation degree of pattern IV depends on the transition time of the corresponding positive ions through the RF sheath which is influenced by the ion mass. In oxygen as well as in argon CCRF plasmas pattern IV is less modulated than in hydrogen CCRF plasmas due to the heavier ions in oxygen and argon. Additionally the modulation degree increases with increasing pressure due to the more confined plasma at higher pressures which is yielding in a stronger modulated ion current towards the powered electrode.
A fluorescent lamp driven with an 'instant start electronic control gear' starts in a glow mode. In the glow mode, which lasts typically for tens of milliseconds, the cathode fall exceeds hundreds of volts. This causes high energy ion bombardment of the electrode which heats the electrode, and induces a transition from glow to arc mode. In the arc mode the electrode emits thermionically and the cathode fall drops to the 12 – 15 V range. Unfortunately, the high energy ion bombardment during the glow mode leads also to intense sputtering of electrode material, including tungsten as well as emitter. Thus, instant started fluorescent lamps often suffer from early failures due to coil fracture. Therefore, the investigation of tungsten erosion during instant start is necessary and was the main goal of this work.
The density of neutral atomic tungsten is determined by laser-induced fluorescence (LIF) and optical emission spectroscopy measurements (OES). Investigations are performed on a low-pressure argon dc discharge and on commercial fluorescent lamps. To include the entire temperature profile along the electrode the diffuse and spot operation modes of the dc lamp are studied experimentally and theoretically. The measured dependencies of the cathode temperature along the coil on the discharge and heating parameters are compared with the calculated results. For the first time the tungsten erosion during instant start of commercial fluorescent lamps was experimentally investigated in this work. The erosion process could be related to sputtering. A reconstruction of the temporal evolution of the absolute tungsten population density of the ground state during the glow mode was presented. The sputtered tungsten density increases immediately with the ignition, reaches a maximum where the discharge contracts at the end of the glow mode, and decreases some milliseconds before the glow-to-arc transition takes place. The maximum tungsten density was observed within a region of a few hundred micrometers only located at the discharge attachment point. The main result achieved in this work is that during the whole glow mode tungsten is sputtered. Therefore, the lifetime of instant started fluorescent lamps can be enhanced by reducing the duration of the glow mode. Additionally, the need for the application of different types of diagnostics for the observation of lamp ignition was shown due to different results of LIF, AAS and OES: The observation of excited tungsten atoms by OES shows the maximum emission signal at the glow-to-arc transition whereas by LIF and AAS measurements of tungsten atoms in the ground state the maximum density is found during the whole glow mode. This can be explained by the fact that the intensity of the spontaneous emitted light is related not only to the density but also to the degree of excitation.
Diese Arbeit untersucht experimentell den Einfluss des metastabilen Zustandes Xe(1s3) und des Resonanzzustandes Xe(1s2) auf die VUV-Strahlungserzeugung in Helium-Xenon-Glimmentladungen (He:Xe = 98:2). Für die Bestimmung der Atomdichten wurde eine experimentelle Anordnung geschaffen, mit der, basierend auf der Methode der Laser-Atom-Absorptionsspektroskopie, orts- und zeitaufgelöste Messungen von optischen Dichten im Säulenplasma durchgeführt wurden. Als Hintergrundstrahlungsquelle kam ein durchstimmbarer Diodenlaser zum Einsatz. Die bereitgestellten Laserwellenlängen von 820 nm bzw. 826 nm entsprechen optischen Übergängen zwischen den Xenonzuständen 6s' 1/2[1/2]0 --> 6p' 1/2[3/2]1 (1s3 --> 2p4) und 6s' 1/2[1/2]1 --> 6p' 1/2[1/2]1 (1s2 --> 2p2).
Den Ausgangspunkt der Untersuchungen stellte die Messung der Absorptionslinienprofile beider Nahinfrarot-Übergänge dar. In Abhängigkeit von den Entladungsparametern Gasdruck, Entladungsstrom und Betriebsweise (Gleichstrom-, gepulste und Wechselstromentladung) wurden daraus die Dichten der angeregten Atome auf der Entladungsachse ermittelt. Durch die Analyse des Abklingens der Besetzungsdichten im Afterglow von gepulst betriebenen Entladungen mit Hilfe eines Systems von gekoppelten Ratengleichungen konnten die dominanten Stoßprozesse für die betrachteten Zustände identifiziert werden. Erstmalig ist in dieser Arbeit die radiale Verteilung der angeregten Spezies Xe(1s3) und Xe(1s2) in He-Xe-Glimmentladungen untersucht worden. Damit ist die VUV-Strahlungsleistung der 129 nm-Linie aus der Dichteverteilung der Resonanzatome ermittelbar.