Refine
Document Type
- Article (5)
- Doctoral Thesis (1)
Language
- English (6)
Has Fulltext
- yes (6)
Is part of the Bibliography
- no (6)
Keywords
- - (5)
- barrier discharge (4)
- gap voltage (3)
- memory effect (3)
- surface charge (3)
- Barrierenentladung (1)
- Laserinduzierte Fluoreszenz (1)
- Plasmadiagnostik (1)
- Stickstoff (1)
- alumina (1)
Institute
Publisher
- IOP Publishing (5)
Abstract
This work reports on the spatio-temporal characterization of the multiple current pulse regime of diffuse barrier discharges driven by sine-wave feeding voltage at a frequency of 2 kHz in helium with small nitrogen admixtures. The discharge gap of 3 mm is bounded by glass plates on both plane electrodes. Priority is given to the lateral discharge inhomogeneities, underlying volume- and surface-memory effects, and the breakdown mechanism. Therefore, relevant processes in the discharge volume and on the dielectric surfaces were investigated by ICCD camera imaging and optical emission spectroscopy in combination with electrical measurements and surface charge diagnostics using the electro-optic Pockels effect of a bismuth silicon oxide crystal. The number of current pulses per half-cycle of the sine-wave voltage rises with increasing nitrogen admixture to helium due to the predominant role of the Penning ionization. Here, the transition from the first glow-like breakdown to the last Townsend-like breakdown is favored by residual species from the former breakdowns which enhance the secondary electron emission during the pre-phase of the later breakdowns. Moreover, the surface charge measurements reveal that the consecutive breakdowns occur alternately at central and peripheral regions on the electrode surface. These spatial inhomogeneities are conserved by the surface charge memory effect as pointed out by the recalculated spatio-temporal development of the gap voltage.
Abstract
Single self-stabilized discharge filaments were investigated in the plane-parallel electrode configuration. The barrier discharge was operated inside a gap of 3 mm shielded by glass plates to both electrodes, using helium-nitrogen mixtures and a square-wave feeding voltage at a frequency of 2 kHz. The combined application of electrical measurements, ICCD camera imaging, optical emission spectroscopy and surface charge diagnostics via the electro-optic Pockels effect allowed the correlation of the discharge development in the volume and on the dielectric surfaces. The formation criteria and existence regimes were found by systematic variation of the nitrogen admixture to helium, the total pressure and the feeding voltage amplitude. Single self-stabilized discharge filaments can be operated over a wide parameter range, foremost, by significant reduction of the voltage amplitude after the operation in the microdischarge regime. Here, the outstanding importance of the surface charge memory effect on the long-term stability was pointed out by the recalculated spatio-temporally resolved gap voltage. The optical emission revealed discharge characteristics that are partially reminiscent of both the glow-like barrier discharge and the microdischarge regime, such as a Townsend pre-phase, a fast cathode-directed ionization front during the breakdown and radially propagating surface discharges during the afterglow.
Surface charge measurements on different dielectrics in diffuse and filamentary barrier discharges
(2017)
Abstract
Previously, we reported on the measurement of surface charges during the operation of barrier discharges (BDs) using the electro-optic Pockels effect of a bismuth silicon oxide (BSO) crystal. With the present work, the next milestone is achieved by making this powerful method accessible to various dielectrics which are typically used in BD configurations. The dynamics and spatial distribution of positive and negative surface charges were determined on optically transparent borosilicate glass, mono-crystalline alumina and magnesia, respectively, covering the BSO crystal. By variation of the nitrogen admixture to helium and the pressure between 500 mbar and 1 bar, both the diffuse glow-like BD and the self-stabilized discharge filaments were operated inside of a gas gap of 3 mm. The characteristics of the discharge and, especially, the influence of the different dielectrics on its development were studied by surface charge diagnostics, electrical measurements and ICCD camera imaging. Regarding the glow-like BD, the breakdown voltage changes significantly by variation of the cathodic dielectric, due to the different effective secondary electron emission (SEE) coefficients. These material-specific SEE yields were estimated using Townsend’s criterion in combination with analytical calculations of the effective ionization coefficient in helium with air impurities. Moreover, the importance of the surface charge memory effect for the self-stabilization of discharge filaments was quantified by the recalculated spatio-temporal behavior of the gap voltage.
Abstract
The presented work highlights the role of residual weakly-bound surface electrons acting as an effective seed electron reservoir that favors the pre-ionization of diffuse barrier discharges (BDs). A glow-like BD was operated in helium at a pressure of 500 mbar in between two plane electrodes each covered with float glass at a distance of
3 mm.The change in discharge development due to laser photodesorption of surface electrons was studied by electrical measurements and optical emission spectroscopy. Moreover, a 1D numerical fluid model of the diffuse discharge allowed the simulation of the laser photodesorption experiment, the estimation of the released surface electrons, and the understanding of their impact on the reaction kinetics in the volume. The breakdown voltage is clearly reduced when the laser beam at photon energy of 2.33 eV hits the cathodic dielectric that is charged with residual electrons during the discharge pre-phase. According to the adapted simulation, the laser releases only a small amount of surface electrons in the order of
10 pC. Nevertheless, this significantly supports the pre-ionization. Using a lower photon energy of 1.17 eV, the transition from the glow mode to the Townsend mode is induced due to a much higher electron yield up to 1 nC. In this case, both experiment and simulation indicate a retarded stepwise release of surface electrons initiated by the low laser photon energy.
Abstract
The laser photodetachment experiment in a diffuse helium–oxygen barrier discharge is evaluated by a 1D fluid simulation. As in the experiment, the simulated discharge operates in helium with
400
ppm
oxygen admixture at
500
mbar
inside a discharge gap of
3
mm
. The laser photodetachment is included by the interaction of negative ions with a temporally and spatially dependent photon flux. The simulation with the usually applied set of reactions and rate coefficients provides a much lower negative ion density than needed to explain the impact on the discharge characteristics in the experiment. Further processes for an enhanced negative ion formation and their capabilities of reproducing the experimental results are discussed. These further processes are additional attachment processes in the volume and the negative ion formation at the negatively charged dielectric. Both approaches are able to reproduce the measured laser photodetachment effect partially, but the best agreement with the experimental results is achieved with the formation of negative ions at the negatively charged dielectric.
The absolute density of the metastable N2(A,v=0) molecule was extensively studied in nitrogen barrier discharges at 500 mbar. For the detection of the metastables laser-induced fluorescence spectroscopy (LIF) was used, at which for the calibration of the absoute metastables density a comparison with Rayleigh scattering was performed. To get the ratio of the LIF signal to the Rayleigh signal it is shown that the LIF signal is the convolution of the Rayleigh signal with an exponential decay. Besides, the different cross sections are calculated and the ratio of the detection sensitivities at the laser and fluorescence wavelength is determined. As a first step on the way to atmospheric pressure barrier discharges, the laser-induced fluorescence spectroscopy was implemented in low pressure capacitively coupled radio-frequency discharges. The determined metastables density in the capacitively coupled radio-frequency discharge is somewhat below 10^12 cm^(-3) at 40 Pa and somewhat below 10^13 cm^(-3) at 1000 Pa. The axial density profiles show a nearly symmetric shape due to the long lifetime of the metastable state. At a pressure of 500 mbar the two discharge modes of the barrier discharge, the filamentary and the diffuse mode, were analysed. The filamentary mode was mainly investigated in an asymmetric discharge configuration. Typical densities in the detection volume are in the range of 10^13 cm^(-3), resulting in maximal densities of up to 10^15 cm^(-3) in the microdischarge channel. Such large densities are in agreement with the fast decay by the pooling reaction after the maximum of the metastables density in the afterglow of the discharge pulse. The time dependent measurements in the afterglow of single microdischarges offer a delay of the metastables production with respect to the discharge current. This delay indicates that the metastables production takes place mostly by cascades from higher triplet states, which are in turn excited by electron impact. The axial density profiles show a maximum in metastables density in front of the anode in agreement with optical emission spectroscopy, but which cannot be clearly identified because of the asymmetric discharge configuration. The measurements for the diffuse discharge mode were performed in a symmetric discharge configuration. The metastables density is in the range of 10^13 cm^(-3). It increases during the current pulse of the discharge and decays afterwards. The maximum of the metastables density is delayed with respect to the maximum of the discharge current. The depletion of metastables in the early discharge afterglow is dominated by the pooling reaction, afterwards quenching by nitrogen atoms becomes important assuming a nitrogen atom density in the order of 10^14 cm^(-3). As for the filamentary mode, the losses by diffusion are negligible for the measurement positions. The measured axial density profiles show an accumulation of metastables in front of the anode, whereas the density in front of the cathode is below the detection limit. To calculate the metastables current density to the dielectrics after the discharge pulse a simulation is developed including the dominant volume processes for the depletion of metastables and the axial diffusion. Starting point for the simulation is the axial metastables density distribution at the end of the discharge pulse. The calculated metastables current density at the dielectrics is in the range of 10^14 cm^(-2)s^(-1). With the use of recently calculated secondary electron emission coefficients a comparison of the secondary electron emission by metastables with the discharge current is done. It is figured out that the secondary electron emission current is large enough to be important during the discharge ignition. To expand the simulation to the whole voltage cycle, the excitation of metastables is assumed to be proportional to the discharge current and electron density. Using this model, the measured time dependences of the metastables density are well reproduced for the investigated parameter variations. This is not the case for the axial profiles, where a metastables loss process is missed to explain the formation of a density plateau in front of the anode during the discharge pulse. The intended calculation of the metastables current density shows that the delay of the metastables production with respect to the discharge current might be responsible for the ignition of microdischarges at the beginning of the discharge pulse.